Airfix Boeing Chinook HC.1 Review
During my pilot training, my home airport had a helicopter company that flew Chinooks. They used them for firefighting and heavy lifting operations. Every so often I see military Chinooks flying over my house as they make their way north to Seattle. You can always tell when a Chinook is coming. It makes a very distinct sound and chop from the two massive rotor blades. It’s yet another aircraft that has meaning to me, which is why I wanted to model this helicopter. I was looking for a good quality model, and when I saw the brand new tooling from Airfix, I knew I needed to get this one. After watching it for a few months during pre-order, I was able to finally find one in stock at a hobby store in Colorado.
Like most builds, this one started with the interior. While the cockpit lacked a little detail, the main cargo/troop area was very detailed. The floor has very sharp lines and lots of detail for the tie downs and hooks. There was also a lot of detail in the walls for the wiring and pipes. As typical with new Airfix kits, the engineering was really well done and everything fit together perfectly.
Building the exterior required a few holes to be drilled. This is the first time I’ve ever seen a jig used to show you exactly where to drill holes. Very unique and it worked quite well. Fitting the two halves of the fuselage together went well, and there is no need to worry about seam lines. Airfix came up with a very unique way of hiding it. They include a trim piece that goes over the top of the fuselage, hiding the seam and adding a lot more detail than would be possible if it was moulded directly on the fuselage.
Windows slot in from the exterior, which made it a breeze to mask and install before painting. The large front windshield needs intricate masking, but it does have raised and recessed details, which made it quite easy to use a knife and cut out masking tape. With everything put together, it was time to paint. I considered replicating the color scheme of the Chinooks at my home airport (white with red stripes), but I decided against it. I wanted a unique paint job and something that I don’t have in my collection. Therefore, I decided to go with the desert sand scheme.
For the paint, I decided to go with a new brand that I haven’t tried before. I chose Mission Models paint since it had the exact color I was looking for and was airbrush ready. I will say that my experience was very disappointing. The paint was so thin that it took several coats to even cover the gray plastic. After a few days of curing, even a light touch would leave a greasy fingerprint that could not be removed. Finally, the paint would peel right off the model if it was masked. In order to try and fix those issues, I sprayed a clear coat to seal it. While it resolved the fingerprint issue, even sticky notes would peel the paint right off the model. I did my best to take extra care when working with it, but there are still some mistakes.
To highlight panels, I used a sand beige color I already had to brighten the centers. After that, decals were applied and a brown panel line wash was applied to darken recesses. Once the weathering was done, I could remove the masking tape and install the landing gear, antennas, and cargo door. Speaking of the cargo door, there are a few options that you can make when building the model. The cargo door can either be closed, half open, or full open with the ramp out. The side door also has 3 stages of open. Depending on which markings you’re going with, there are a few parts choices that can be made. The desert scheme has a dust filter for the engine, where the standard scheme has a normal intake.
The last step in the build was the rotor blades. Airfix was able to achieve a very realistic droop on the blades. I’ve modeled a few helicopters, and this is the first one that had a very natural curve to it. The rotor hubs themselves were decent, but simple and not a lot going on. To give some more life to the black blades and hubs, I dry brushed them with buff paint to lend more credibility to the fact that this helicopter was used in the desert.
Overall this kit was a real joy to build. Fit was excellent and the engineering was really well done. Details were amazing and the level of options and features for a kit this small was exciting. I really like new Airfix kits, and I would definitely recommend this kit to anyone no matter their experience level.








More reviews
- Academy T-34B Mentor Review
- Eduard L-39 Albatros Review
- Italeri V-22 Osprey Review
- Tamiya A-1H Skyraider Review
- Minicraft Cessna Citation I Review
- Revell Porsche 911 Carrera Review
- Minicraft Beechcraft Bonanza V35 Review
- Revell F-15E Strike Eagle Review
- Building an Abandoned Ghostbusters ECTO-1
- Anigrand C-17 Globemaster III Review