Italeri V-22 Osprey Review
My first encounter with the V-22 was when I was 13. I was on a road trip from Portland to Seattle. When I was passing through Tacoma, I saw a V-22 hovering over the highway having just departed from Fort Lewis. I had never seen anything like that before. This was nearly 10 years before I got my pilot’s license and had a real interest in aircraft. Despite that, it was an amazing sight to see as it transitioned from hover to airplane mode. Fast forward 10 years and now I’m in San Diego. During the drive from Los Angeles, I passed by the Oceanside VOR and a sign that warned about dust clouds from helicopters. Just then as I turned the corner, a V-22 from Camp Pandleton was hovering a few feet off the ground making a quite impressive dust cloud. Ever since I knew this is a subject I wanted to model.
The kit I picked up is an Italeri kit. I got it from a swap meet and it was partially started. No research went into which kit was the best, but I knew that I wanted to represent this in 1/48 scale. After going through the parts to make sense of what the previous owner had done, I went straight to detailing the interior. The instructions make questionable color callouts. For a majority of this, I referenced photos online. The interior is fairly well detailed with lots of wiring and plumbing on the walls. The cockpit is pretty basic which is a shame since there is a giant window in the front to show it all off. For the cargo door you have the choice of either closed or open. If you want to have the door open, you will need to perform some minor surgery and cut the door in half.
While I was waiting for glue to dry, I moved on to building the engines. Fit was fairly poor and there were lots of gaps that needed to be filled. Care was given to make sure that the blades could still be moved once everything was put together. There is decent detail on the engines as well as the fuselage, however most of it is raised rivets and panel lines. You’ll need to take care when sanding to not destroy that detail or redo it after the fact. Engines can be installed in hover or airplane mode. I went for hover mode but you will need to be careful with handling afterwards. They don’t fit very snugly and there is a lot of wobble and play in the engines once installed.
Now it was time for my least favorite part of the build: putting the two halves of the fuselage together. Fit was horrible and countless hours were spent sanding, trimming, filling, and priming. This is the most amount of time I have ever spent cleaning up seams and fitting the halves together. Lots of test fitting was needed and trimming of the fuselage floor was required. Despite all of that, there were still major gaps. Looking back I probably should have used epoxy putty to fill those gaps, but instead I went with several applications of Tamiya white putty and Vallejo putty to smooth everything. In the end you can still see the seam and it’s not nearly as smooth as I was hoping for.
With that setback, I was a little discouraged that this might not be as good of a model as I was hoping for. While it may not be contest worthy, I still wanted to give it a good paint job. I started by priming the whole model with Mr. Surfacer 1000. Then I pre-shaded the panels with black. Now it was time for paint. I painted the bottom half with Vallejo Model Air dark ghost gray and the top half with Vallejo Model Air dark gull gray. I make sure to leave enough of the black shading to show through but not so much that it was distracting. In the end I think I may have covered it up too much. I will fix that later on.
Decals were pretty good. There aren't a ton of them, but sometimes I prefer when it’s not so much that it looks messy. My only issue is that the color of the decals is so close to the color of paint I used that a few of them completely disappear. Once the decals were done, it was time for weathering. After referencing photos, it seems like most of them are fairly dirty. To enhance the panel lines, I used pastels. Since they are raised, I couldn’t use a wash, but a light dry brush of pastel dust worked perfectly. A brown wash was used on the engines to add oil stains and a black wash on the interior to deepen the shadows and enhance the detail on the walls.
Overall I’m really pleased with the look of the model. I think the paint job turned out great and the pastel weathering worked perfectly. I’m a little disappointed that there is still a nasty seam line on the nose of the aircraft. After all of that time and work I still couldn't get it perfect. Sometimes that’s just the way some kits are. Not all of them can be winners and this one just happened to be an unlucky mold. But I learned a lot and know about many new things that I can apply to future models. I wouldn’t recommend this kit, but if you do have one in your stash, be prepared for lots of cleanup, filling, and sanding.







More reviews
- Academy T-34B Mentor Review
- Airfix Boeing Chinook HC.1 Review
- Eduard L-39 Albatros Review
- Tamiya A-1H Skyraider Review
- Minicraft Cessna Citation I Review
- Revell Porsche 911 Carrera Review
- Minicraft Beechcraft Bonanza V35 Review
- Revell F-15E Strike Eagle Review
- Building an Abandoned Ghostbusters ECTO-1
- Anigrand C-17 Globemaster III Review